STOCK #110089 REF #110089
REFURBISHED 2006
SPECIFICATIONS: STOCK # 110089
SWING..........................: 14"
DISTANCE BETWEEN CENTERS.......: 36"
SWIVEL TABLE GRADUATIONS:
TOWARD WHEELHEAD..........: 9.5 DEGREES OR 5.5 PER FOOT
AWAY FROM WHEELHEAD.......: 2.5 DEGREES OR 1" PER FOOT
GRINDING WHELLHEAD.............: 14" X 1.5" C 5" I.D.
SWIVEL RANGE:
UPPER SWIVEL...................: NO GRADUATIONS
LOWER SWIVEL...................: 90 DEGREES LEFT & 90 DEGREES RIGHT
GRINDING WHELL SPEED...........: 1745 RPM APPROX. (CAN BE CHANGED
W/DIFFERENT PULLEY RATIO)
INTERNAL GRINDING SPINDLE......: 13,800 RPM APPROX. (UP TO 25,000 RPM
W/DIFFERNT PULLEYS)
TABLE:
TRAVERSE RATES.................: INFINITE
RANGE OF TABLE TRAVERSE RATES..: 3" TO 150" (INCHES PER MINUTE)
HAND TABLE TRAVERSE:
I- RAPID: 1.000" PER REVOLUTION OF HANDWHEEL
II-SLOW: 100" PER REVOLUTION OF HANDWHEEL
3 FOLLOWER RESTS
HEADSTOCK & FOOTSTOCK
HEADSTOCK NO. 12 JARNO
COMBINATION LIVE OR DEAD SPINDLE
FOOTSTOCK: NO 9 JARNO TAPER
SPINDLE SPEEDS..................: 40 TO 400 RPM INFINATELY VARIABLE
SPINDLE NOSE TAPER..............: D-16" CAMLOCK WITH 1-3/8" HOLE
HEADSTOCK SWIVLE:
i - TOWARD WHEEL HEAD: 90 DEGREES
8" 4-JAW CHUCK, 10" FACE PLATE
INFEED ADJUSTMENTS:
A) DIAMETER REDUCTION PER REVOLUTION OF INFEED HANDWHEEL: .100
B) MINIMUM INFEED INCREMENT: 0001
C) AUTOMATIC INFEED AT TABLE REVERSAL:
i - DWELL AT REVERSAL
D) MAXIMUM INFEED TRAVEL: 8"
E) RAPID HYDRAULIC INFEED & RETRACT
LUBRICATION SYSTEM
A) CONSTANT PRESSURE FROM HYDRAULIC SYSTEM
ELECTRICAL
A) GRINDING WHEELHEAD: 3 HP, 1745 RPM, 208-220/440 VOLTS, 9.0/4.5
AMPS, 3 PHASE
B) I.D. MOTOR, 1 HP, 3450 RPM, 208-220/440 VOLTS, 3.0/1.5 AMPS, 3
PHASE
C) HEADSTOCK: 3/4 HP, 1140 RPM, 115 VOLTS, DC
D) HYDRAULIC PUMP: 3/4 HP, 1145 RPM, 208-220/440 VOLTS, 2.9/1.45 AMPS,
3 PHASE
E) COOLANT PUMP: 1 HP, 1725 RPM, 208-220/440 VOLTS, 3 PHASE
WEIGHT: 11,000 LBS
RE-MANUFACTURED:
THE MACHINE WILL BE 100% DISSAMBLED. ALL BEARINGS, BRONZE BLUSHINGS,
SEALS AND PACKINGS WILL BE REPLACED WITH NEW. OTHER PARTS WILL BE
RELACED THAT SHOW ANY APPRECIABLE WEAR THAT WOULD BE DETRIMENTAL TO
THE PERFORMANCE OF THE MACHINE.
THE HYDRAULIC COMPNENTS WILL BE DISASSEMBLED, CLEANED AND
RE-ASSEMBLED. ANY UNITS SHOWING APPRECIABLE WEAR WILL BE REBUILT.
ALL EXTERNAL PARTS WILL BE SANDBLASTED OR GLASS BEADED TO BARE METAL
AND PAINTED TO A FACTORY QUALITY FINISH WITH TWO PART EPOXY PAINT.
ALL WAY SURFACES WILL BE PRECISION GROUND TO BETTER THAN NEW
TOLERANCES AND/OR HAND SCRAPED. ORIGINAL FACTORY GEOMETRIC ALIGNMENTS
WILLBE EXCEEDED PER SPECIFICATIONS.
THE MACHINE WILL BE RE-ASSEMBLED AND TESTED TO VERIFY BETTER THAN
FACTORY NEW TOLERANCES.
PRICE....................: ${please call for price}
